Datacomm 45-0010 Recessed Media Box User Manual download pdf

Parts Included

: See Figure 1

1. Recessed Media Box

2. Wall Plate

3. Wall Plate Screws (4)

4. Retrofit Mounting Tabs (4)

5. Retrofit Mounting Wings with Screws (4)

6. Black Foam Tape

7. #6 Wood Screws (2)

8. Small Threaded Screws (4)

9. Screwdriver (Not Pictured)

For New Construction with Stud Mounted Installation Only

1. Select the location for mounting the recessed media box.

2. See Figure 2: Break the four (4) retrofit mounting tabs

off. It is very important to break off all four (4) retrofit

mounting tabs when installing for new construction.

3. Using the stud positioning marks – align the recessed

media box to the stud.

4. Using the two supplied wood screws, secure the

recessed media box to the stud through the two (2)

mounting holes.

5. Next, install the drywall (wallboard) with a cutout opening

of approximately 7-3/8” x 5-5/16”.

6. Tighten the four (4) wing bracket mounting screws.

When wing bracket screws are tightened, the box is

drawn firmly against the drywall.

7. Using the four (4) mounting screws, install the flexible

cover plate.

Installation of the recessed media box for new construction is

now complete. See wiring instructions for low voltage and line

voltage installation.

Installation Instructions for Retrofit Only

1. Select the location for mounting the recessed media box.

2. The recessed media box is designed to be mounted

between two studs. Using a stud finder, locate and mark

the studs that are behind the drywall. Make sure the

studs are at least 11” apart.

3. Locate the four (4) drywall opening locating pins on the

back of the cover plate (see Figure 3). After selecting

the location for the recessed media plate, press the back

of the cover plate against the drywall allowing the four

drywall opening locating pins to mark the outline of the

recessed cable plate opening on the drywall. Use a ruler

or straight edge object to connect the drywall locating pin

holes to form an opening for the recessed media box.

Using a drywall saw, cut the traced opening out of the

drywall thus creating a hole approximately 7-3/8” x

5-5/16” to insert the recessed media box into the wall.

4. While inserting the recessed media box into the wall, the

four (4) retrofit mounting tabs will stop the recessed

media box at the drywall. Next, tighten the four (4) wing

bracket mounting screws. When wing bracket screws

are tightened, the box is drawn firmly against the drywall.

5. Use the four (4) mounting screws to install the flexible

cover plate.

DataComm Electronics, Inc.

6349 Peachtree Street

Norcross, GA 30071-1725

888.223.7977

770.662.8205

www.datacommelectronics.com

Instruction / Installation Sheet

DataComm Electronics 45-0010 Recessed Media Box

Figure 1

Figure 2

Figure 3

5/18/09 Rev. 2

1 2

5/18/09 Rev. 2 2

Summary of Contents

Page 1

Parts Included: See Figure 1 1. Recessed Media Box 2. Wall Plate 3. Wall Plate Screws (4) 4. Retrofit Mounting Tabs (4) 5. Retrofit

Page 2 - 5/18/09 Rev. 2

Low Voltage and Line Voltage Wiring Instructions: This product is to be installed in accordance with all electrical codes and regulations. Please

Comments to this Manuals

No comments

Datacomm 45-0010 Recessed Media Box User Manual

Browse online or download User Manual for Home Theater Systems Datacomm 45-0010 Recessed Media Box. DataComm 45-0010 Recessed Media Box User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Home Theater Systems Datacomm 45-0010 Recessed Media Box